CISCO CCNP 642-901 BSCI Exam Tutorial: EIGRP Adjacencies And Secondary Addresses By Chris Bryant At Isnare.com Ezine Articles

I've read some non-Cisco documentation that EIGRP will not allow adjacencies to form when secondary addresses are used. This is incorrect, but there is one common error that can result if both addresses are not secondary. To fully prepare for the 642-901 BSCI exam, you should know about this error. Let's take a look at R2 and R3, which will be using secondary addresses to form an EIGRP adjacency across an ethernet segment.

R2(config)#interface ethernet0

R2(config-if)#ip address 172.12.23.2 255.255.255.0

R2(config-if)#ip address 23.23.23.2 255.255.255.0 secondary

R2(config)#router eigrp 100

R2(config-router)#no auto-summary

R2(config-router)#network 23.23.23.0 0.0.0.255

R3(config)#interface ethernet0

R3(config-if)#ip address 172.12.23.3 255.255.255.0

R3(config-if)#ip address 23.23.23.3 255.255.255.0 secondary

R3(config)#router eigrp 100

R3(config-router)#no auto-summary

R3(config-router)#network 23.23.23.0 0.0.0.255

Here's the partial output of show ip eigrp neighbor on R3:

R3#show ip eigrp neighbor

IP-EIGRP neighbors for process 100

H Address Interface

0 172.12.23.2 Et0

The adjacency has formed! Note the address is actually the primary IP address on the interface, even though we used the secondary network number in the EIGRP network command. Personally, I stay away from secondary network numbers if at all possible, but you should know that secondary IP addresses can be used to create EIGRP adjacencies.

What's the common error with using secondary addresses, you asked? It's when an address from the same subnet is the primary interface address on one neighbor and the secondary interface address on another. Let's say we had configured R2 and R3 as follows:

R2(config)#int e0

R2(config-if)#ip address 23.23.23.2 255.255.255.0

R3(config)#interface ethernet0

R3(config-if)#ip address 172.12.23.3 255.255.255.0

R3(config-if)#ip address 23.23.23.3 255.255.255.0 secondary

On R2, we get this message:

01:54:05: IP-EIGRP: Neighbor 172.12.23.3 not on common subnet for Ethernet0 (23.23.23.2 255.255.255.0)

Since we configured 23.23.23.2 as a primary interface address on R2, the EIGRP process is looking at the primary interface address on potential neighbors. R3's primary ethernet0 address is 172.12.23.2, so you get the "not on common subnet" error message - and what you don't get is an adjacency! That's something to be aware of on your 642-901 BSCI exam as well as when working with EIGRP in production networks.

Published At: Isnare Free Articles Directory http://www.isnare.com
Permanent Link: http://www.isnare.com/?aid=117769&ca=Computers+and+Technology

Important Notice DISCLAIMER: All information, content, and data in this article are sole opinions and/or findings of the individual user or organization that registered and submitted this article at Isnare.com without any fee. The article is strictly for educational or entertainment purposes only and should not be used in any way, implemented or applied without consultation from a professional. We at Isnare.com do not, in anyway, contribute or include our own findings, facts and opinions in any articles presented in this site. Publishing this article does not constitute Isnare.com's support or sponsorship for this article. Isnare.com is an article publishing service. Please read our Terms of Service for more information.