iSnare.com - Free Content Articles Directory
Authors Contents [Advanced Search][Add OpenSearch][Job Search]
Distribute your articles to thousands of article sites for only $2 and below! Read more...

Index  Computers and Technology
 

Cisco CCNA/CCNP Home Lab Tutorial: Configuring An Access Server

 
[ Contact the Author] [ Send to a Friend] [ Article Publisher] [Make PDF] [ Print] [ Bookmark & Share]
 
Read our Terms of Service before reprinting this article. The submitter specified above has claimed the rights to this article.
Chris Bryant

As your CCNA / CCNP home lab expands, an access server such as the Cisco 2509 or 2511 is one of the best investments you can make. In this article, we'll look at the basic configuration for an access server and discuss how to connect to the other routers and switches in your pod through the AS.

Here's part of a configuration from one of my access servers:

ip host FRS 2006 100.1.1.1

ip host SW2 2005 100.1.1.1

ip host SW1 2004 100.1.1.1

ip host R2 2002 100.1.1.1

ip host R1 2001 100.1.1.1

ip host R3 2003 100.1.1.1

interface Loopback0

ip address 100.1.1.1 255.255.255.255

no ip directed-broadcast

This is an IP Host table, and this is what makes the entire AS setup work. Your PC will connect to the access server, and the access server is in turn physically connected to your other routers and switches via an octal cable. One end of the octal cable splices off into eight separate cables, each terminated with an Rj-45 connector. That connector will be placed into the console port of one of your home lab devices. In this configuration, I have connector 1 connected to the console port of R1, connector 2 to R2, connector 3 to R3, connector 4 to Sw1, and so forth. (The connectors are physically numbered as well.)

The IP Host table entries here are linked to the loopback address shown. The loopback can be any address, but it must match the address in the IP Host table. This allows you to create reverse telnet sessions to the routers and switches.

To open the reverse telnet sessions upon opening a connection to the AS, type the entire name of the device and press the enter key twice. A connection to that device will now be visible, as shown here:

Access_Server#r1

Trying R1 (100.1.1.1, 2001)... Open

R1#

To get back to the access server, use the key combination followed by pressing the "x" key. Keep doing this until you've opened a connection to every router and switch in your pod.

Once you've opened the lines, you will not use the full device name to connect to the home lab devices. You should press only the number corresponding to the reverse telnet session you opened. For instance, in this configuration I opened telnet session 1 to R1, session 2 to R2, and session 3 to R3. Once I opened those sessions, I just use those numbers to reconnect to the devices, as shown here:

Access_server#1

[Resuming connection 1 to r1 ... ]

R1#

Access_server#2

[Resuming connection 2 to r2 ... ]

R2#

Access_server#3

[Resuming connection 3 to r3 ... ]

R3#

If you type the full hostname again after initially opening the connection, you will see this message:

Access_server#r1

Trying R1 (100.1.1.1, 2001)...

% Connection refused by remote host

The connection is refused because you already have an open connection to that router.

There's one more important part of an access server config your CCNA / CCNP home lab will need:

line 1 8

no exec

transport input all

The line numbers may differ according to your access server, but "no exec" is very important here. This will stop rogue EXEC sessions from refusing connections that it shouldn't be refusing. Without this command, you'll commonly see "connection refused by remote host" when you shouldn't be. That message is the most common error you'll see on an access server, and it's there because you already have an open connection or you left "no exec" out of your configuration. "No exec" isn't mandatory, but it will help you keep your sanity!

Important NoticeDISCLAIMER: All information, content, and data in this article are sole opinions and/or findings of the individual user or organization that registered and submitted this article at Isnare.com without any fee. The article is strictly for educational or entertainment purposes only and should not be used in any way, implemented or applied without consultation from a professional. We at Isnare.com do not, in anyway, contribute or include our own findings, facts and opinions in any articles presented in this site. Publishing this article does not constitute Isnare.com's support or sponsorship for this article. Isnare.com is an article publishing service. Please read our Terms of Service for more information.

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (http://www.thebryantadvantage.com ), home of free CCNA and CCNP tutorials, and The Ultimate CCNA and CCNP Study Packages. For a copy of his FREE "How To Pass The CCNA" or "CCNP" ebook, visit the website and download your copies!
Article Tags: access [See Dictionary], connection [See Dictionary], host [See Dictionary]
Got a question about this article? Ask the community!
Article published on March 21, 2006 at Isnare.com
 
Rate this article:

CISCO CCNA, CCENT, And CCNP Home Lab Study: The DTE/DCE Cable
Submitted by: Chris Bryant

More Cisco CCNA, CCENT, and CCNP candidates than ever before are putting together their own home labs for their certification exam study, and that's a great trend - there's nothing like learning on the real thing...

Cisco 640-802 Ccna And Ccent Certification: Ram, Rom, Nvram, Flash, And The Boot Process
Submitted by: Chris Bryant

An important part of your Cisco CCENT and CCNA certification studies is learning the differences between RAM, ROM, NVRAM, and Flash memory...

Cisco CCNA / CCENT Certification Exam Training: Physical And Virtual Lans
Submitted by: Chris Bryant

Earning your Cisco CCENT certification and passing the 640-822 exam demands that you master networking basics, and part of that is knowing how to work with both physical and virtual Local Area Networks (LANs)...

CISCO CCNP Certification Training Tutorial: Priority Queuing for the ONT Exam
Submitted by: Chris Bryant

You can’t earn your CCNP certification without passing the Cisco ONT exam, and queuing is a huge topic on that exam...

CISCO CCNP Certification Exam Training for the ONT Exam: QoS Models
Submitted by: Chris Bryant

A large part of your CCNP training for the ONT certification exam should be spent studying the various ways we can implement Quality of Service (QoS) on Cisco routers and switches...

CISCO CCNA / CCENT Certification Exam Training: Broadcasts, Hubs, Routers, And Switches
Submitted by: Chris Bryant

In a previous Cisco CCENT certification exam tutorial, we talked about broadcasts and the potential of a broadcast storm...

CISCO CCENT / CCNA Certification Exam Tutorial: Comparing TCP and UDP Headers
Submitted by: Chris Bryant

During your Cisco CCENT and CCNA studies, you'll see that so many great TCP features - the three-way handshake, windowing, sequence numbering, error detection and recovery - are strictly TCP features...

CISCO Certification: An Introduction To Multilayer Switching And SVIs
Submitted by: Chris Bryant

Sure, you have to know all about SVIs and multilayer switching to earn your CCNP, but you also need to know about them because they’re so commonplace in today’s networks...

CISCO CCNA / CCNP Certification Exam Tutorial: EIGRP And Split Horizon
Submitted by: Chris Bryant

EIGRP is a major topic for your CCNA and CCNP studies, and one basic skill you’ll need to pass your Cisco certification exams is to identify situations where you need to enable or disable split horizon...

CISCO CCNP 642-901 BSCI Exam Tutorial: EIGRP Adjacencies And Secondary Addresses
Submitted by: Chris Bryant

I've read some non-Cisco documentation that EIGRP will not allow adjacencies to form when secondary addresses are used...

CISCO CCNP Certification BSCI 642-901 Exam Training: The EIGRP Adjacency
Submitted by: Chris Bryant

EIGRP is an important part of real-world networking as well as being a major topic on the 642-901 CCNP BSCI exam...

Ccna Certification Exam Training: Circuit Switching Vs. Packet Switching
Submitted by: Chris Bryant

CCNA certification exam training is all about learning the details, and an important part of your CCNA test prep is knowing the differences between Cisco router and switch technologies that are somewhat similar...

CISCO CCNA Certification Exam Tutorial: The Config Register And Password Recovery
Submitted by: Chris Bryant

Whether you're preparing for the CCNA certification exam or not, you must be prepared for the following question: "Hey, I reloaded this router and it wants an enable password...

Comptia Network+ Certification Exam Tutorial: Virus Attacks And Antivirus Programs
Submitted by: Chris Bryant

Whether you’re preparing to pass the Network+ or Cisco CCNA certification exam or not, you must not underestimate the importance of antivirus programs and virus definition updates...

Comptia Network+ Certification Exam Tutorial: Antivirus Programs
Submitted by: Chris Bryant

In the first part of this CompTIA Network+ certification exam tutorial, we looked at the different types of viruses and other invaders trying to get into our network, and how antivirus programs help to stop them...

How to Install Aftermarket Stereo in Vauxhall Agila
Submitted by: Jack Wylde

DESCRIPTION: The radio installation in VAUXHALL AGILA Some Cars have steering controls from new and when you replace your radio...

Don't Ruin Your Laminator - 4 Reasons to Always Use a Carrier With Your Pouch Laminating Machine
Submitted by: Jeff McRitchie

One of the most important supplies you'll need when getting ready to use a pouch laminator is a carrier...

5 Reasons to Consider the Destroyit 4107 Cross Cut Shredder
Submitted by: Jeff McRitchie

There is shredding, and then there is "Shredding" The Destroyit 4107 is a heavy duty shredder that can handle just about anything any sized office can throw at it...

Reviewing the Akiles CombMac 24E Electric Plastic Comb Binding Machine
Submitted by: Jeff McRitchie

Because it is a rare electric comb binding systems on the market that works with legal size sheets, the Akiles CombMac 24E already has somewhat of a competitive advantage...

Reviewing the Akiles DuoMac 321 Combination 3:1 and 2:1 Pitch Wire Binding Machine
Submitted by: Jeff McRitchie

Offering some nice flexibility in binding styles, the Akiles DuoMac 321 is positioned as a binding solution for businesses and organizations that want the ability to bind documents in as many as five binding styles...

Reviewing the Akiles DuoMac 421 Combination 4:1 Pitch Coil and 2:1 Pitch Wire Binding Machine
Submitted by: Jeff McRitchie

The Akiles DuoMac 421 is a combination binding system that offers medium volume users with three different binding styles...

Windows Registry Cleaner - Registry Easy Review
Submitted by: Carlos Castro

Windows Registry Cleaner programs are a dime a dozen Having used several myself I can speak with confidence that no two registry cleaners are exactly the same...

PC Virus Removal Can Help Businesses Save Millions of Dollars
Submitted by: Adrianna Noton

The business world is now, for the most part, driven by technology The internet is of fundamental importance to the success of a business...

GBC ShredMaster CC195 Cross-Cut Shredder Review
Submitted by: Jeff McRitchie

If you've visited an office supply store recently or checked out paper shredders on the Internet, it probably seems like paper shredders are all alike, especially in the looks department...

Frequently Asked Questions About Spiral Coil Binding
Submitted by: Jeff McRitchie

Coil binding - also known as spiral binding - is a very popular method of binding, but it can be difficult to understand how it's done...

An Overview of the GBC C-75 Comb Binding Machine
Submitted by: Jeff McRitchie

If you are looking for an inexpensive comb binding machine for your office or home office you might be considering the GBC C75...

5 Great Features of the Rhin-O-Tuff HD6500
Submitted by: Jeff McRitchie

Designed for the heaviest duty users such as print and copy shops, binderies and large organizations, the Rhino Tuff HD6500 is a machine that offers top of the line flexibility and capacity...

Sony Ericsson W595 Mobile Phone Review - The Latest and Best Walkman Phone?
Submitted by: Carlson Osbourne

The one thing that most Sony Ericsson phones have in abundance is good looks No matter what lies beneath the surface, they all tend to have unique and beautiful appearances that can enhance the style factor of everyone using them...

Comparing the Swingline SmartCut EasyBlade and EasyBlade Plus Rotary Trimmers
Submitted by: Jeff McRitchie

At first glance, Swingline's SmartCut EasyBlade and EasyBlade Plus may look very similar, except for the price...

Five Reasons to Consider the Rhino-Tuff OD4000 Modular Binding Punch
Submitted by: Jeff McRitchie

Though it may be the smallest of Rhino's electric interchangeable punches, the OD4000 offers you about as much as a binding punch can offer...

Isnare.com Footer Divider

© 2004-2009. Isnare Free Articles - An Isnare Online Technologies Free Articles Project. All Rights Reserved.   Privacy Policy