CCNP Certification / BCMSN Exam Tutorial: HSRP Mac Addresses And Timers By Chris Bryant At Isnare.com Ezine Articles

To earn your CCNP certification and pass the BCMSN exam, you've got to know what HSRP does and the many configurable options. While the operation of HSRP is quite simple (and covered in a previous tutorial), you also need to know how HSRP arrives at the MAC address for the virtual router - as well as how to configure a new MAC for this virtual router. This puts us in the unusual position of creating a physical address for a router that doesn't exist!

The output of show standby for a two-router HSRP configuration is shown below.

R2#show standby

Ethernet0 - Group 5

Local state is Standby, priority 100

Hellotime 3 sec, holdtime 10 sec

Next hello sent in 0.776

Virtual IP address is 172.12.23.10 configured

Active router is 172.12.23.3, priority 100 expires in 9.568

Standby router is local

1 state changes, last state change 00:00:22

R3#show standby

Ethernet0 - Group 5

Local state is Active, priority 100

Hellotime 3 sec, holdtime 10 sec

Next hello sent in 2.592

Virtual IP address is 172.12.23.10 configured

Active router is local

Standby router is 172.12.23.2 expires in 8.020

Virtual mac address is 0000.0c07.ac05

2 state changes, last state change 00:02:08

R3 is in Active state, while R2 is in Standby. The hosts are using the 172.12.123.10 address as their gateway, but R3 is actually handling the workload. R2 will take over if R3 becomes unavailable.

An IP address was assigned to the virtual router during the HSRP configuration process, but not a MAC address. However, there is a MAC address under the show standby output on R3, the active router. How did the HSRP process arrive at a MAC of 00-00-0c-07-ac-05?

Well, most of the work is already done before the configuration is even begun. The MAC address 00-00-0c-07-ac-xx is reserved for HSRP, and xx is the group number in hexadecimal. That's a good skill to have for the exam, so make sure you're comfortable with hex conversions. The group number is 5, which is expressed as 05 with a two-bit hex character. If the group number had been 17, we'd see 11 at the end of the MAC address - one unit of 16, one unit of 1.

The output of the show standby command also tells us that the HSRP speakers are sending Hellos every 3 seconds, with a 10-second holdtime. These values can be changed with the standby command, but HSRP speakers in the same group should have the same timers. You can even tie down the hello time to the millisecond, but it's doubtful you'll ever need to do that.

R3(config-if)#standby 5 timers ?

Hello interval in seconds

msec Specify hello interval in milliseconds

R3(config-if)#standby 5 timers 4 ?

Hold time in seconds

R3(config-if)#standby 5 timers 4 12

Another important HSRP skill is knowing how to change the Active router assignment. I'll show you how to do that, and how to configure HSRP interface tracking, in the next part of my CCNP / BCMSN exam tutorial!

Published At: Isnare Free Articles Directory http://www.isnare.com
Permanent Link: http://www.isnare.com/?aid=50740&ca=Computers+and+Technology

Important Notice DISCLAIMER: All information, content, and data in this article are sole opinions and/or findings of the individual user or organization that registered and submitted this article at Isnare.com without any fee. The article is strictly for educational or entertainment purposes only and should not be used in any way, implemented or applied without consultation from a professional. We at Isnare.com do not, in anyway, contribute or include our own findings, facts and opinions in any articles presented in this site. Publishing this article does not constitute Isnare.com's support or sponsorship for this article. Isnare.com is an article publishing service. Please read our Terms of Service for more information.